期刊检索

  • 2026年第34卷
  • 2025年第33卷
  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:杜佳旭,刘忠军,焦燕妮,雷娟,敖庆波.Cu掺杂TiSi多孔管状膜材料的制备及孔结构表征[J].材料科学与工艺,2026,34(5):46-57.DOI:10.11951/j.issn.1005-0299.20250057.
DU Jiaxu,LIU Zhongjun,JIAO Yanni,LEI Juan,AO Qingbo.Preparation and pore structure characterization of Cu-doped TiSi porous tubular membrane materials[J].Materials Science and Technology,2026,34(5):46-57.DOI:10.11951/j.issn.1005-0299.20250057.
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 351次   下载 27次 本文二维码信息
码上扫一扫!
Cu掺杂TiSi多孔管状膜材料的制备及孔结构表征
杜佳旭1, 刘忠军1, 焦燕妮1, 雷娟1, 敖庆波2
(1.西安石油大学 材料科学与工程学院,西安 710065;2.金属多孔材料国家重点实验室(西北有色金属研究院),西安 710016)
摘要:
本研究采用离心沉积结合限域原位反应烧结技术制备了Cu掺杂TiSi多孔膜管状材料,旨在探究Cu掺杂量及烧结温度对膜层微观结构、物相组成、孔隙性能及膜基结合强度的影响,并评估Cu掺杂提升Ti5Si3梯度膜层完整性的可行性。使用X射线衍射仪(XRD)、能谱仪(EDS)和扫描电镜(SEM)对多孔材料的物相组成、元素含量和微观形貌进行了分析;利用多孔材料完整性测试仪对样品过滤性能和孔隙性能进行了测试;利用力学试验机测试了管状样品的膜/基结合强度;以检测结果为基础,对限域原位反应烧结机理及物相演变路径进行了简要分析。结果表明:所制备的多孔膜表面主要物相为Ti5Si3,并伴随生成TiO化合物、TiCu及CuO。提高Cu掺杂量和烧结温度,使得膜层逐渐完整,厚度逐渐增加,相对透气系数和最大冒泡孔径都呈下降趋势,膜/基结合强度呈增加趋势;当温度为1 050 ℃时,膜/基结合强度达到了44.06 MPa。
关键词:  TiSi体系  原位反应  多孔膜  Cu掺杂  孔结构
DOI:10.11951/j.issn.1005-0299.20250057
分类号:TF124
文献标识码:A
基金项目:陕西省重点研发计划(2022QCY-LL-59);西安石油大学校青年创新团队项目(2019QNKYCXTD12);西安市科技局秦创原转化孵化能力提升项目(24ZHFH0006);西安石油大学研究生创新基金(YCX2413120).
Preparation and pore structure characterization of Cu-doped TiSi porous tubular membrane materials
DU Jiaxu1, LIU Zhongjun1, JIAO Yanni1, LEI Juan1, AO Qingbo2
(1. School of Materials Science and Engineering, Xi’an Shiyou University, Xi’an 710065, China;2. State Key Laboratory of Porous Metal Materials (Northwest Institute for Nonferrous Metal Research), Xi’an 710016, China)
Abstract:
This study successfully synthesized Cu-doped TiSi porous tubular membrane materials through an integrated approach combining centrifugal deposition with confined in-situ reactive sintering. Structural characterization was performed via Xray diffraction (XRD), energy-dispersive spectroscopy (EDS), and scanning electron microscopy (SEM) to investigate phase composition, elemental distribution, and microstructural evolution. The filtration performance and pore characteristics were systematically evaluated using a porous material integrity tester, while membrane/substrate bonding strength was quantified through universal mechanical testing. The research systematically investigates the effects of Cu doping concentration and sintering temperature on four critical parameters: membrane layer morphology, phase constitution, pore characteristics, and interfacial bonding strength. Key findings reveal that the membrane surface primarily consists of Ti5Si3 matrix phase, accompanied by TiO compounds, TiCu and CuO. As increasing the Cu doping amount and sintering temperature, the membrane thickness gradually increased, the relative permeability coefficient and the maximum bubbling pore size both decreased, and the membrane/substrate bonding strength gradually increased. When the membrane was synthesized at 1 050 ℃, the membrane/base bonding strength reached 44.06 MPa.
Key words:  TiSi system  in-situ reaction  porous membrane  Cu doping  pore structure

友情链接LINKS