期刊检索

  • 2026年第34卷
  • 2025年第33卷
  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:童璟芸,王纯凯,郭照生,李珺,尹元德,张义伟.T22钢无缝管顶管过程壁厚精度分析[J].材料科学与工艺,2026,34(4):45-56.DOI:10.11951/j.issn.1005-0299.20250003.
TONG Jingyun,WANG Chunkai,GUO Zhaosheng,LI Jun,YIN Yuande,ZHANG Yiwei.Analysis of wall thickness accuracy of T22 seamless steel tube in push bench process[J].Materials Science and Technology,2026,34(4):45-56.DOI:10.11951/j.issn.1005-0299.20250003.
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 635次   下载 57次 本文二维码信息
码上扫一扫!
T22钢无缝管顶管过程壁厚精度分析
童璟芸1,王纯凯2,郭照生2,李珺2,尹元德1,张义伟1
(1.安徽工业大学 冶金工程学院,安徽 马鞍山 243002;2.江苏常宝普莱森钢管有限公司,江苏 常州 213200 )
摘要:
应用Simufact软件对典型规格荒管顶管过程中的壁厚不均问题进行三维弹塑性有限元模拟,研究顶管过程中轧件的金属流动、应力应变、横向及纵向壁厚分布规律,并对模拟结果进行了物理验证。在分析壁厚不均产生原因的基础上,对4个可调机架旋转30°改善荒管的横向壁厚不均,并通过辊缝压下对荒管头尾壁厚进行削减。结果表明:荒管横向壁厚分布为孔顶处到侧壁30°处壁厚值逐渐增大,侧壁30°处到辊缝处壁厚值逐渐减小;荒管纵向壁厚分布为头部壁厚偏薄,中段壁厚值相对平稳且略微增大,尾部壁厚增厚;可调机架旋转30°后,荒管侧壁30°处最大壁厚值减薄明显,孔顶和辊缝处最小壁厚值有所增加,横向壁厚不均度明显改善,由原工艺的6.98%下降到4.04%;当辊缝压下0.2 mm时,荒管头尾壁厚削减值分别为0.22和0.13 mm,横向壁厚不均度分别为3.71%和4.84%;当辊缝压下0.5 mm时,荒管头尾壁厚削减值分别为0.35和0.26 mm,横向壁厚不均度分别为3.24%和4.36%。本研究可为顶管机组实施荒管头尾壁厚削尖工艺提供科学依据。
关键词:  T22钢  CPE顶管  壁厚精度  应力应变  数值模拟
DOI:10.11951/j.issn.1005-0299.20250003
分类号:TG335.1
基金项目:钢铁联合基金重点资助项目(U186021).
Analysis of wall thickness accuracy of T22 seamless steel tube in push bench process
TONG Jingyun1,WANG Chunkai2,GUO Zhaosheng2,LI Jun2,YIN Yuande1,ZHANG Yiwei1
(1.School of Metallurgy Engineering, Anhui University of Technology, Ma’anshan 243002, China; 2.Jiangsu Changbao Plesson Seamless Steel Tube Co., Ltd., Changzhou 213200, China)
Abstract:
Due to the problem of uneven wall thickness of typical specification hollow tube generated by push bench process, a three-dimensional elastoplastic finite element simulation was carried out by using Simufact software. The metal flow, stressstrain, transverse and longitudinal wall thickness distribution of rolled piece during push bench process were studied. The simulation results are verified by measured wall thickness data from practical production. Based on the analysis of the causes of the uneven wall thickness, the transverse wall thickness of the hollow tube was improved by rotating four adjustable stands by 30°, and the wall thickness value of the head and tail of the hollow tube was reduced by regulating the roll gap reduction. The results show that the transverse wall thickness distribution of the rolled tube gradually increases from the top of the groove to the area near 30° of the side wall, and gradually decreases from the area near 30° of the side wall to the roll gap. The longitudinal wall thickness distribution of the hollow tube is thin in the area near the head of the rolled tube, the wall thickness in the middle of the rolled tube is relatively stable and increases slightly, and the wall thickness at the tail of the rolled tube increases. When the adjustable stands are rotated by 30°, the maximum wall thickness value at 30° of the side wall of the hollow tube is obviously reduced, the minimum wall thickness value at the top of the groove and the roll gap is increased, and the transverse wall thickness unevenness is obviously improved, which decreases from 6.98% of the original process to 4.04%. When the roll gap reduction is 0.2 mm, the wall thickness reductions of the head and tail of the hollow tube are 0.22 mm and 0.13 mm respectively, and the transverse wall thickness unevenness is 3.71% and 4.84% respectively. When the roll gap reduction is 0.5 mm, the wall thickness reductions of the head and tail of the hollow tube are 0.35 mm and 0.26 mm respectively, and the transverse wall thickness unevenness is 3.24% and 4.36% respectively. This study provides a scientific basis for implementing the tapering process of the head and tail of the hollow tube on push bench mill.
Key words:  T22 steel  CPE push bench  wall thickness accuracy  stress-strain  numerical simulation

友情链接LINKS