期刊检索

  • 2026年第34卷
  • 2025年第33卷
  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:陈正南,纠永涛,刘豪,伍里峰,王朋旭,张雷,丁宗业,王培.PCBN刀具周边磨削工艺实验研究[J].材料科学与工艺,2026,34(4):36-44.DOI:10.11951/j.issn.1005-0299.20250040.
CHEN Zhengnan,JIU Yongtao,LIU Hao,WU Lifeng,WANG Pengxu,ZHANG Lei,DING Zongye,WANG Pei.Experimental study on peripheral grinding process of PCBN tools[J].Materials Science and Technology,2026,34(4):36-44.DOI:10.11951/j.issn.1005-0299.20250040.
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 720次   下载 77次 本文二维码信息
码上扫一扫!
PCBN刀具周边磨削工艺实验研究
陈正南1,纠永涛1,2,刘豪1,伍里峰2,王朋旭2,张雷2,丁宗业3,王培4
(1.宁波大学 机械工程与力学学院,浙江 宁波 315211; 2.中国机械总院集团宁波智能机床研究院有限公司,浙江 宁波 315600;3.上海交通大学 材料科学与工程学院,上海 315700; 4.河南工业大学 材料科学与工程学院,郑州 450002)
摘要:
为研究PCBN刀具的周边磨削加工性能,通过单因素实验探究砂轮粒度、砂轮线速度和进给速度对磨削力、表面质量和刃口缺陷度的影响规律。采用压电测力仪实时监测法向力与切向力,结合三维形貌测量仪、超景深显微镜及扫描电镜分别表征表面粗糙度、刃口缺陷及微观结构特征,并基于Hertz接触理论和裂纹扩展机制解析材料去除机理。结果表明:砂轮粒度、砂轮线速度和进给速度对法向磨削力的影响幅度较大,对切向磨削力的影响幅度相对较小;表面粗糙度整体波动较小,但砂轮粒度增大导致材料表面0.2至0.6 μm的凹坑划痕数量明显增多,表面磨损形貌由沿晶裂纹逐渐转向解理脆性断裂;刃口缺陷度随砂轮粒度减小显著降低,随砂轮线速度、进给速度的增大呈先降后升趋势,并在W7粒度、25 m/s线速度及1.0 mm/min进给速度的磨削条件下最小;微观形貌分析表明,磨削表面及刃口的磨损方式主要为冲击脆性去除、沿晶裂纹、穿晶断裂和刻划作用。
关键词:  PCBN刀具  磨削机理  磨削力  表面质量  刃口缺陷度
DOI:10.11951/j.issn.1005-0299.20250040
分类号:TH162
基金项目:高端数控机床与基础制造装备国家科技重大专项(2024ZD0710301);浙江省“尖兵”“领雁”研发攻关计划项目(2024C01086).
Experimental study on peripheral grinding process of PCBN tools
CHEN Zhengnan1,JIU Yongtao1,2,LIU Hao1,WU Lifeng2,WANG Pengxu2,ZHANG Lei2,DING Zongye3,WANG Pei4
(1.Faculty of Mechanical Engineering and Mechanics, Ningbo University, Ningbo 315211, China;2.China Academy of Machinery Ningbo Academy of Intelligent Machine Tool Co., Ltd., Ningbo 315600, China;3.School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 315700, China;4.School of Material Science and Engineering, Henan University of Technology, Zhengzhou 450002, China)
Abstract:
To study the peripheral grinding performance of PCBN tools, single-factor experiments were performed to examine the impacts of abrasive grit size, wheel speed, and feed rate on grinding forces, surface quality, and edge chipping. Normal and tangential forces were measured in real time via a piezoelectric dynamometer, while surface roughness, edge defects and microstructural characteristics were analyzed using 3D profilometry, depth microscopy, and SEM. The material removal mechanism was elucidated through Hertz contact theory and crack propagation analysis. Results showed that abrasive grit size, speed, and feed rate had greater effects on normal force than tangential force. Surface roughness remained stable, but coarser grits increased the number of surface pits and scratches ranging from 0.2 μm to 0.6 μm, with surface wear morphology transitioning from intergranular cracks to cleavage brittle fractures. Edge chipping decreased with finer grits, and showed initial decrease followed by increase trends with wheel speed and feed rate, reaching minimum values under W7 grain size, 25 m/s wheel speed, and 1.0 mm/min feed rate. Microscopic analysis revealed that wear mechanisms at ground surfaces and edges mainly included impact-induced brittle removal, intergranular cracking, transgranular fracture, and ploughing effects.
Key words:  PCBN tools  grinding mechanism  grinding force  surface quality  edge chipping

友情链接LINKS