期刊检索

  • 2026年第34卷
  • 2025年第33卷
  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:党坤,占发琦,郑月红,许世鹏.复合镍铝涂层高温氯化物熔盐腐蚀行为和机理研究[J].材料科学与工艺,2026,34(4):57-67.DOI:10.11951/j.issn.1005-0299.20250113.
DANG Kun,ZHAN Faqi,ZHENG Yuehong,XU Shipeng.Research on the corrosion behavior and mechanism of high-temperature chloride molten salt in composite NiAl coatings[J].Materials Science and Technology,2026,34(4):57-67.DOI:10.11951/j.issn.1005-0299.20250113.
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 660次   下载 69次 本文二维码信息
码上扫一扫!
复合镍铝涂层高温氯化物熔盐腐蚀行为和机理研究
党坤1,占发琦2,郑月红2,许世鹏1
(1.酒泉职业技术大学 甘肃省太阳能发电系统重点实验室,甘肃 酒泉 735000;2.兰州理工大学 省部共建有色金属先进加工与再利用国家重点实验室,兰州 730050)
摘要:
氯化物熔盐有望成为新一代光热发电储热介质,这对系统关键零部件耐高温熔盐腐蚀性提出了更高要求。镍铝涂层可作为不锈钢表面耐氯化物熔盐高温腐蚀保护涂层材料,但需要对其耐蚀行为和相关机理进行深入研究。本文采用磁控溅射技术制备SiNiAl/Al/NiAl复合涂层,研究了SiNiAl/Al/NiAl涂层和预氧化后涂层微观组织以及高温氯化物熔盐腐蚀行为。结果表明,预氧化后的涂层将3层涂层融合为一体,形成了氧化铝层;经过高温氯化物熔盐腐蚀后的复合涂层中出现MgCr2O4、NiAl2O4、NiAl和Al2O3,形成的Al2O3层具有耐高温氯化物熔盐腐蚀性,腐蚀速率较低,约为43.0 μm/a,与其它材料相比,表现出明显优势;SiNiAl/Al/NiAl涂层腐蚀后Al2O3层厚度达到6.1 μm,明显高于NiAl和SiNiAl单层涂层腐蚀后Al2O3层厚度(分别为1.1和2.9 μm)。复合涂层增加了Al2O3层的厚度,增强了Al2O3层生长和修复缺陷的能力,有助于提升涂层耐高温氯化物熔盐腐蚀性能。
关键词:  腐蚀的控制与防护  镍铝涂层  氯化物熔盐  腐蚀  聚光太阳能热发电
DOI:10.11951/j.issn.1005-0299.20250113
分类号:TG174
基金项目:甘肃省重点研发计划(24YFGF001);甘肃省太阳能发电系统重点实验室开放课题(2024SPKL02).
Research on the corrosion behavior and mechanism of high-temperature chloride molten salt in composite NiAl coatings
DANG Kun1, ZHAN Faqi2, ZHENG Yuehong2, XU Shipeng1
(1.Jiuquan Vocational and Technical University, Key Laboratory of Solar Power System, Jiuquan 735000, China;2.Lanzhou University of Technology, State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou 730050, China)
Abstract:
Chloride molten salt is expected to become a new generation of heat storage media for solar thermal power generation. This imposes stricter requirements on the high-temperature molten salt corrosion resistance of key system components. However, the application of NiAl coating as a protective layers on stainless steel surfaces against high-temperature chloride molten salt corrosion still requires in-depth research. In order to study the high-temperature corrosion resistance of NiAl coatings in chloride molten salts, SiNiAl/Al/NiAl composite coatings were prepared by magnetron sputtering technology. The microstructure and resistance to high-temperatures molten chloride salt corrosion of SiNiAl/Al/NiAl coating were investigated. The pre-oxidation integrated SiNiAl/Al/NiAl multilayer coating into a unified structure, resulting in the formation of a continuous dense oxide layer. The corroded coating contains MgCr2O4, NiAl2O4, NiAl and Al2O3. The formed Al2O3 layer is resistant to high-temperature chloride molten salt corrosion, with a relatively low corrosion rate, remaining at approximately 43.0 μm/a. Compared with other materials, it shows obvious advantages. The thickness of the Al2O3 layer after corrosion of the SiNiAl/Al/NiAl coating reached 6.1 μm, while the thicknesses of the Al2O3 layer after corrosion of the NiAl and SiNiAl coatings were 1.1 μm and 2.9 μm, respectively. This indicates that the composite coating increased the thickness of the Al2O3 layer and enhanced the ability of the Al2O3 layer to grow and repair defects. This enhances the corrosion resistance of the coating.
Key words:  control and protection of corrosion  NiAl coating  chloride molten salt  corrosion  CSP

友情链接LINKS