期刊检索

  • 2026年第34卷
  • 2025年第33卷
  • 2024年第32卷
  • 2023年第31卷
  • 2022年第30卷
  • 2021年第29卷
  • 2020年第28卷
  • 2019年第27卷
  • 2018年第26卷
  • 2017年第25卷
  • 2016年第24卷
  • 2015年第23卷
  • 2014年第22卷
  • 2013年第21卷
  • 2012年第20卷
  • 2011年第19卷
  • 2010年第18卷
  • 第1期
  • 第2期

主管单位 中华人民共和国
工业和信息化部
主办单位 中国材料研究学会
哈尔滨工业大学
主编 苑世剑 国际刊号ISSN 1005-0299 国内刊号CN 23-1345/TB

期刊网站二维码
微信公众号二维码
引用本文:张琳,尹涵,李云爻,高雪娇.基于水平微米线阵列的CVD石墨烯周期性应变研究[J].材料科学与工艺,2026,34(3):37-43, 62.DOI:10.11951/j.issn.1005-0299.20250077.
ZHANG Lin,YIN Han,LI Yunyao,GAO Xuejiao.Horizontal microwires array enabled periodic strain in CVD graphene[J].Materials Science and Technology,2026,34(3):37-43, 62.DOI:10.11951/j.issn.1005-0299.20250077.
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被:浏览 922次   下载 75次 本文二维码信息
码上扫一扫!
基于水平微米线阵列的CVD石墨烯周期性应变研究
张琳,尹涵,李云爻,高雪娇
(华北电力大学(保定) 数理系 河北省物理学与能源技术重点实验室,河北 保定 071003)
摘要:
针对在化学气相沉积(Chemical Vapor Deposition,CVD)石墨烯上难以施加周期性应变的问题,对湿法转移过程进行了优化,并分析了微米线高度对应变的影响。首先,通过延长铜基底刻蚀时间、提高目标衬底洁净度、旋涂均匀的PMMA覆盖层等方法优化了CVD石墨烯湿法转移过程,使得石墨烯上的破损显著减少且可重复性高。其次,使用优化后的湿法转移技术将CVD石墨烯转移至不同高度的水平微米线上。最后,利用光学显微镜和微区拉曼快速成像对石墨烯的形貌以及质量进行了表征分析。研究结果表明,水平微米线间隔处的CVD石墨烯上产生明显的周期性拉应变,单轴拉应变值受到水平微米线高度的影响:30、285 nm高的微米线分别对石墨烯施加了0.16%、0.54%的单轴拉应变,而560 nm高的微米线则导致微米线间隔处的石墨烯普遍发生断裂。该结果对于二维材料的周期性应变工程具有参考价值。
关键词:  CVD石墨烯  湿法转移  水平微米线  单轴拉应变  周期性
DOI:10.11951/j.issn.1005-0299.20250077
分类号:O472+.91
文献标识码:A
基金项目:
Horizontal microwires array enabled periodic strain in CVD graphene
ZHANG Lin,YIN Han,LI Yunyao,GAO Xuejiao
(Hebei Key Laboratory of Physics and Energy Technology, Department of Mathematics and Physics, North China Electric Power University, Baoding 071003, China)
Abstract:
To apply periodic strain on chemical vapor deposition (CVD) graphene, the wet transfer process was optimized, and the influence of the height of the microwires on the strain was analyzed. First, the wet transfer process for CVD graphene was optimized by increasing the etching time of copper substrate, improving the cleanness of target substrate, and coating a uniform PMMA layer. As a result, the cracks on the transferred graphene were significantly reduced, and reproducibility improved. Secondly, CVD graphene was transferred onto horizontal microwires array of different heights using the optimized wet transfer method. Finally, the morphology and quality of graphene were characterized via an optical microscope and micro-area Raman rapid imaging. The relevant results showed that periodic tensile strain was generated on the CVD graphene at the intervals of horizontal microwires. The uniaxial tensile strain value was affected by the height of the horizontal microwires: the 30-nm-high and 285-nm-high microwires induced 0.16% and 0.54% uniaxial tensile strain to the graphene, respectively, while the 560-nm-high microwires caused widespread cracks on the graphene at the intervals of the microwires. These results have reference value for periodic strain engineering in 2D materials.
Key words:  CVD graphene  wet transfer  horizontal microwires array  uniaxial tensile strain  periodicity

友情链接LINKS