期刊检索

  • 2026年第58卷
  • 2025年第57卷
  • 2024年第56卷
  • 2023年第55卷
  • 2022年第54卷
  • 2021年第53卷
  • 2020年第52卷
  • 2019年第51卷
  • 2018年第50卷
  • 2017年第49卷
  • 2016年第48卷
  • 2015年第47卷
  • 2014年第46卷
  • 2013年第45卷
  • 2012年第44卷
  • 2011年第43卷
  • 2010年第42卷
  • 第1期
  • 第2期

主管单位 中华人民共和国工业和信息化部 主办单位 哈尔滨工业大学 主编 李隆球 国际刊号ISSN 0367-6234 国内刊号CN 23-1235/T

期刊网站二维码
微信公众号二维码
引用本文:肖军,霰建平,仝朝康,马建勇,王培杰,刘永健.悬索桥主缆缠丝张力损失特征与机理[J].哈尔滨工业大学学报,2026,58(7):166.DOI:10.11918/202412066
Xiao Jun,Xian Jianping,Tong Chaokang,Ma Jianyong,Wang Peijie,Liu Yongjian.Characteristics and mechanisms of tension loss in the helical wrapping wires of main cables in suspension bridges[J].Journal of Harbin Institute of Technology,2026,58(7):166.DOI:10.11918/202412066
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
过刊浏览    高级检索
本文已被:浏览 166次   下载 56次 本文二维码信息
码上扫一扫!
分享到: 微信 更多
悬索桥主缆缠丝张力损失特征与机理
肖军1,2,3,霰建平1,2,仝朝康1,2,马建勇1,2,王培杰1,2,刘永健1,3
(1.陕西省“四主体一联合”桥梁工程智能建造技术校企联合研究中心,西安 710199; 2.中交第二公路工程局有限公司,西安 710065;3.长安大学 公路学院,西安 710064)
摘要:
为研究悬索桥主缆缠丝的防护效果,采用精细化有限元模型结合实桥试验的方法研究了缠丝过程中的缠丝张力变化,并基于验证后的有限元模型分析了缠丝导入力、主缆直径及主缆径向弹性模量对缠丝张力损失的影响,提出了考虑缠丝阶段张力损失的缠丝导入力计算公式并改进了现有缠丝工艺。试验研究结果表明:缠丝阶段的张力损失主要是由后续缠丝张力引起主缆径向变形导致,张力损失呈现先快后慢,然后逐渐趋于稳定的特征,缠丝阶段的张力损失在26.3%~37.3%之间;测试位置处缠丝张力稳定时,缠丝机较测试位置处平均前进距离为25.2 cm。有限元分析结果表明:主缆直径及径向弹性模量对缠丝力损失比例影响显著,且主缆直径及径向弹性模量与缠丝力损失比例均成反比例关系;主缆直径为851.9 mm情况下,主缆直径增大50%,缠丝力损失比例从27.8%减小至13.7%,主缆径向弹性模量从1 052 MPa增加至3 052 MPa,缠丝力损失从27.8%减小至11.3%。在试验及有限元分析结果基础上,提出了考虑缠丝阶段张力损失的导入力计算公式,进一步优化了缠丝导入力的计算;提出了一种基于缠丝张力损失机理的新型缠丝工艺,可有效减小缠丝过程中的张力损失。
关键词:  桥梁工程  主缆缠丝  缠丝试验  缠丝张力损失  缠丝有限元仿真  安全系数  主缆预紧
DOI:10.11918/202412066
分类号:U443
基金项目:
Characteristics and mechanisms of tension loss in the helical wrapping wires of main cables in suspension bridges
Xiao Jun1,2,3,Xian Jianping1,2,Tong Chaokang1,2,Ma Jianyong1,2,Wang Peijie1,2,Liu Yongjian1,3
(1.Shaanxi Union Research Center of University and Enterprise for Bridge Intelligent Construction, Xi′an 710199, China; 2.CCCC Second Highway Engineering Bureau Co., Ltd., Xi′an 710065, China; 3.School of Highway, Chang′an University, Xi′an 710064, China)
Abstract:
To investigate the protective effectiveness of strand wrapping wire in suspension bridge main cables, a method combining refined finite element models with full-scale bridge testing was adopted to study the variations in wrapping wire tension throughout the process. Based on the validated finite element models, the impacts of the wrapping wire insertion force, main cable diameter, and main cable radial elastic modulus on tension loss were analyzed. A formula for calculating the wrapping wire insertion force, which takes into account tension loss during the wrapping wire stage, was proposed, and the existing wrapping wire process was improved. Experimental results indicate that tension loss during the wrapping wire stage is primarily caused by radial deformation of the main cable due to subsequent wrapping wire tensions. The tension loss exhibits an initial rapid decrease, followed by a slower rate, and gradually stabilizes, ranging between 26.3% and 37.3%. When the wrapping wire tension stabilizes at the test location, the wrapping wire machine advances an average distance of 25.2 cm relative to the test position. Finite element analysis results reveal that the main cable diameter and radial elastic modulus have significant effects on the proportion of wrapping wire force loss, with both factors showing an inverse proportional relationship with the force loss ratio. In the case of a main cable with a diameter of 851.9 mm, an increase in the main cable diameter by 50% reduces the wrapping wire force loss ratio from 27.8% to 13.7%, and an increase in the main cable radial elastic modulus from 1 052 MPa to 3 052 MPa reduces the force loss from 27.8% to 11.3%. Based on the experimental and finite element analysis results, a formula for calculating the insertion force that considers tension loss during the wrapping wire stage was further refined. Additionally, a novel wrapping wire process based on Mechanism of wrapping wire tension loss was introduced, which can effectively reduce tension loss during the wrapping wire process.
Key words:  bridge engineering  main cable wrapping wire  wrapping wire test  wrapping wire tension loss  finite element simulation of wrapping wire  safety factor  main cable pre-tightening

友情链接LINKS