| 引用本文: | 王小鹏,周勇军,侯培源,李毅,刘一力,王博.大跨度悬索桥吊索连接件叉形耳板磨损对其疲劳寿命的影响[J].哈尔滨工业大学学报,2026,58(7):109.DOI:10.11918/202505017 |
| Wang Xiaopeng,Zhou Yongjun,Hou Peiyuan,Li Yi,Liu Yili,Wang Bo.Effect of wear on fatigue life of fork-ear plate in hanger connectors of long-span suspension bridges[J].Journal of Harbin Institute of Technology,2026,58(7):109.DOI:10.11918/202505017 |
|
| |
|
|
| 本文已被:浏览 160次 下载 61次 |
 码上扫一扫! |
|
|
| 大跨度悬索桥吊索连接件叉形耳板磨损对其疲劳寿命的影响 |
|
王小鹏1,2,周勇军1,侯培源1,李毅1,3,刘一力4,王博4
|
|
(1.长安大学 公路学院,西安 710064; 2.陕西铁路工程职业技术学院,陕西 渭南 714000; 3.广东省公路建设有限公司湾区特大桥养护技术中心,广州 510635;4.长安大学 工程机械学院,西安 710064)
|
|
| 摘要: |
| 为探索吊索连接件磨损产生机理,量化叉形耳板的磨损深度,评估磨损对其疲劳寿命的影响,首先,通过现场调研与磨屑检测,确定磨损损伤部位,明确磨损产生机理;然后,基于实际车流数据与GNSS监测数据分析吊索索力和吊索连接件的纵向相对角度;最后,应用Archard模型量化叉形耳板的磨损深度,并对其进行疲劳寿命评估。结果表明:吊索连接件褐红色磨屑的主要成分是Fe2O3,主要来源于叉形耳板与箱梁耳板之间的磨损,未检测到关节轴承的磨屑,吊索退扭和缆梁相对运动是造成耳板磨损的根本原因;吊索连接件纵桥向相对转角主要位于-3°~3°之间,且符合高斯分布;该桥运营5 a后,叉形耳板磨损深度约为0.207 mm,磨损深度随着时间的增长不断增大,但增长速度不断减小;运营5、10、15、20、25、30 a后,吊索连接件叉形耳板疲劳寿命分别损失了7.59%、13.08%、18.89%、23.75%、28.54%、33.23%。吊索钢丝的退扭和耳板间的磨损都会降低叉形耳板的疲劳寿命,在设计吊索连接件时应予以充分考虑。 |
| 关键词: 桥梁工程 悬索桥 吊索连接件 疲劳寿命 退扭效应 磨损深度 |
| DOI:10.11918/202505017 |
| 分类号:U448 |
| 基金项目:广东省交通集团科技项目(JT2021YB15) |
|
| Effect of wear on fatigue life of fork-ear plate in hanger connectors of long-span suspension bridges |
|
Wang Xiaopeng1,2,Zhou Yongjun1,Hou Peiyuan1,Li Yi1,3,Liu Yili4,Wang Bo4
|
|
(1.School of Highway, Chang′an University, Xi′an 710064, China; 2.Shaanxi Railway institute, Weinan 714000, Shaanxi, China; 3.Bay Area Super Major Bridge Maintenance Technology Center of Guangdong Highway Construction Co., Ltd., Guangzhou 510635, China; 4.School of Construction Machinery, Chang′an University, Xi′an 710064, China)
|
| Abstract: |
| To investigate the wear mechanism of hanger connectors, quantify the wear depth of the fork-ear plate, and evaluate its impact on fatigue life, this study first identified wear damage locations and clarified the wear mechanism through field investigations and wear debris analysis. Based on actual traffic data and GNSS monitoring data, the hanger cable force and the longitudinal relative angle of the connectors were analyzed. The Archard model was then applied to quantify the wear depth of the fork-ear plate, followed by fatigue life assessment. The results indicate that the brown-red wear debris from hanger connectors primarily consists of Fe2O3, originating from wear between the fork-ear plate and the box-girder ear plate, with no wear debris from the spherical bearing detected. Hanger back-twist and cable-girder relative motion are the root causes of plate wear. The relative longitudinal rotation angle of hanger connectors predominantly ranges between -3° and 3°, following a Gaussian distribution. After 5 years of service, the wear depth of the fork-ear plates reaches approximately 0.207 mm, exhibiting progressive growth over time but with a decelerating rate. The fatigue life loss of the fork-ear plate after 5,0, 5,0, 25, and 30 years of operation is 7.59%, 13.08%, 18.89%, 23.75%, 28.54%, and 33.23%, respectively. Both hanger back-twist and wear between plates significantly reduce the fatigue life of the fork-ear plate, necessitating comprehensive consideration in the design of hanger connectors. |
| Key words: bridge engineering suspension bridge hanger connector fatigue life back-twist effect wear depth |
|
|
|
|