期刊检索

  • 2026年第58卷
  • 2025年第57卷
  • 2024年第56卷
  • 2023年第55卷
  • 2022年第54卷
  • 2021年第53卷
  • 2020年第52卷
  • 2019年第51卷
  • 2018年第50卷
  • 2017年第49卷
  • 2016年第48卷
  • 2015年第47卷
  • 2014年第46卷
  • 2013年第45卷
  • 2012年第44卷
  • 2011年第43卷
  • 2010年第42卷
  • 第1期
  • 第2期

主管单位 中华人民共和国工业和信息化部 主办单位 哈尔滨工业大学 主编 李隆球 国际刊号ISSN 0367-6234 国内刊号CN 23-1235/T

期刊网站二维码
微信公众号二维码
引用本文:陈鹏宇,杨冰晨,药天运,许方舟,赵煜,周勇军.3D打印CFRP-Ⅰ型层间断裂韧性的断层替换测试法及参数化分析[J].哈尔滨工业大学学报,2024,56(11):88.DOI:10.11918/202310014
CHEN Pengyu,YANG Bingchen,YAO Tianyun,XU Fangzhou,ZHAO Yu,ZHOU Yongjun.Fracture layer replacement method and parameterized analysis of modeⅠ inter-layer fracture toughness of 3D printing CFRP[J].Journal of Harbin Institute of Technology,2024,56(11):88.DOI:10.11918/202310014
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【下载PDF阅读器】  【关闭】
过刊浏览    高级检索
本文已被:浏览 660次   下载 873次 本文二维码信息
码上扫一扫!
分享到: 微信 更多
3D打印CFRP-Ⅰ型层间断裂韧性的断层替换测试法及参数化分析
陈鹏宇1,杨冰晨1,药天运2,许方舟1,赵煜1,周勇军1
长安大学 公路学院,西安 710064;长安大学 建筑工程学院,西安 710061
摘要:
为实现3D打印碳纤维增强树脂基复合材料(carbon fiber reinforced polymer,CFRP)Ⅰ型层间断裂韧性的测试分析,并量化评价打印参数对该型断裂韧性的影响规律,推进3D打印CFRP技术在桥梁工程中的应用,分别从试验及仿真角度开展了相关探索。首先,提出了一种新型的3D打印CFRP层间预制裂纹制备方法-断层替换法,利用该方法开展了系统性的试验研究,分析了两类关键打印参数对Ⅰ型层间断裂韧性的影响规律。其次,基于内聚区理论及surface-based cohesive关系,构建了各类打印工况下的预制裂纹试件双悬臂梁(double cantilever beam,DCB)试验的仿真模型,并完成了仿真计算与试验测试的对比分析。结果表明:3D打印CFRP的Ⅰ型层间断裂韧性随着打印温度及速度的提高而增大,且打印温度对断裂韧性的影响更显著,当温度由245 ℃升至285 ℃时,断裂韧性提高了294.6%;当速度由20 mm/s增至60 mm/s时,断裂韧性提高了27.6%;当打印温度与速度提高时,试件在打印过程中热量散失更小,Ⅰ型层间力学性能得到提高; 但当打印速度过大时,印材在打印过程中无法完全沉积并实现较好的黏结,反而对Ⅰ型层间力学性能造成负面影响。同时,仿真结果与试验数据的相对误差均控制在15%以内,表明提出的断层替换法在Ⅰ型层间断裂韧性试验数据获取方面是合理且稳定的。因此,该方法可为后续量化评价3D打印CFRP桥梁工程构件的层间力学性能提供试验技术支撑。
关键词:  桥梁工程  3D打印CFRP  Ⅰ型层间断裂韧性  断层替换法  内聚区理论
DOI:10.11918/202310014
分类号:TB332
文献标识码:A
基金项目:国家重点研发计划(2021YFB1600302);长安大学中央高校基本科研业务费专项资金(300102282108);陕西省自然科学基金(2022JM-275)
Fracture layer replacement method and parameterized analysis of modeⅠ inter-layer fracture toughness of 3D printing CFRP
Pengyu CHEN1, Bingchen YANG1, Tianyun YAO2, Fangzhou XU1, Yu ZHAO1, Yongjun ZHOU1
School of Highway, Chang′an University, Xi′an 710064, China;School of Civil Engineering, Chang′an University, Xi′an 710061, China
Abstract:
In order to test and analyze the mode Ⅰ inter-layer fracture toughness of 3D printing carbon fiber reinforced polymer (CFRP), and quantitatively evaluate the influence of printing parameters on the mode Ⅰ fracture toughness, then promote the application of 3D printing CFRP technology in bridge engineering, experimental and simulation methods were used to carry out the relevant explorations, during this study. Firstly, a novel method for preparing inter-layer pre-cracks of 3D printing CFRP was proposed, namely fracture layer replacement method. Systematic experimental research was conducted by this method, and the influence of two types of key printing parameters on the mode Ⅰ inter-layer fracture toughness was analyzed. Secondly, based on the cohesive zone theory and the surface-based cohesive relationship, simulation models of the double cantilever beam (DCB) test specimens with pre-cracks under various printing conditions were established. Meanwhile, a comparative analysis between simulation and experiment was carried out. The results indicate that the mode Ⅰ inter-layer fracture toughness of 3D printing CFRP increases with the increase of printing temperature and printing speed, and the effect of printing temperature is more significant. When the temperature increases from 245 ℃ to 285 ℃, the fracture toughness increases by 294.6%. When the printing speed increases from 20 mm/s to 60 mm/s, the fracture toughness increases by 27.6%. When the printing temperature and speed are increased, the heat loss of specimen in the printing process is smaller, and the mode Ⅰ inter-layer mechanical properties are improved. However, excessive printing speed can hinder complete deposition and optimal bonding, resulting in negative effects on the mode Ⅰ inter-layer mechanical properties. Moreover, the relative errors between simulation results and experimental data are controlled within 15%, which indicates that the fracture replacement method proposed in this study is reasonable and stable in terms of obtaining test data of type Ⅰ inter-layer fracture toughness. Therefore, this method can provide experimental technical support for the subsequent quantitative evaluation of inter-layer mechanical properties of 3D printing CFRP bridge engineering components.
Key words:  bridge engineering  3D printing CFRP  mode Ⅰ inter-layer fracture toughness  fracture layer replacement method  cohesion zone theory

友情链接LINKS