| 引用本文: | 武亮亮,许瑞达,焦泽辉,于慧臣.激光选区熔化TC4合金的拉伸行为研究[J].材料科学与工艺,2025,33(6):43-49.DOI:10.11951/j.issn.1005-0299.20240155. |
| WU Liangliang,XU Ruida,JIAO Zehui,YU Huichen.The study on tensile behavior of selective laser melting TC4 alloy[J].Materials Science and Technology,2025,33(6):43-49.DOI:10.11951/j.issn.1005-0299.20240155. |
|
| |
|
|
| 本文已被：浏览 286次 下载 176次 |
码上扫一扫！ |
|
|
| 激光选区熔化TC4合金的拉伸行为研究 |
|
武亮亮1,2,3,许瑞达1,2,3,焦泽辉1,2,3,于慧臣1,2,3
|
|
(1. 中国航发北京航空材料研究院,北京 100095; 2.中国航空发动机集团 材料检测与评价重点实验室,北京 100095;3. 航空材料检测与评价北京市重点实验室,北京 100095)
|
|
| 摘要: |
| 利用激光选区熔化技术(Selective Laser Melting,SLM)制备TC4合金,使用电子万能试验机、扫描电子显微镜、光学显微镜等设备研究了热等静压后SLM TC4合金不同取样方向(垂直和水平)的组织形貌与拉伸性能,并与合金的退火态进行对比分析。结果表明:TC4合金在进行热等静压处理后,沿打印方向(垂直)显示为延伸的β柱状晶结构,而在垂直打印方向(水平)显示为等轴晶形貌,柱状晶内为α集束与α+β网篮组织混合形貌,不同于退火态,热等静压后合金的α板条变宽,长径比减小；相对于退火态,热等静压后合金水平和垂直方向强度及塑性无明显各向异性,垂直和水平方向试样抗拉强度分别为965和975 MPa,断后伸长率分别为15.5%和16.5%,综合力学性能优异；拉伸断口呈韧窝特征,断裂机制为韧性断裂。 |
| 关键词: TC4合金 激光选区熔化 显微组织 拉伸性能 各向异性 |
| DOI：10.11951/j.issn.1005-0299.20240155 |
| 分类号:TG146.2 |
| 文献标识码:A |
| 基金项目:国家重点研发计划(2017YFB0702004);财政部稳定支持基础研究计划基金项目(KZ0C190727)；中国航发科技创新平台项目(CXPT-2023-035). |
|
| The study on tensile behavior of selective laser melting TC4 alloy |
|
WU Liangliang1,2,3, XU Ruida1,2,3, JIAO Zehui1,2,3, YU Huichen1,2,3
|
|
(1.AECC Beijing Institute of Aeronautical Materials, Beijing 100095,China;2.Beijing Key Laboratory of Aeronautical Materials Testing and Evaluation, Beijing 100095,China;3.Key Laboratory of Aeronautical Materials Testing and Evaluation, Aero Engine Corporation of China, Beijing 100095,China)
|
| Abstract: |
| TC4 alloy was fabricated using the Selective Laser Melting (SLM) technique, and its microstructural morphology and tensile properties after hot isostatic pressing (HIP) were investigated in different sampling directions (vertical and horizontal) using a universal testing machine, scanning electron microscope, and optical microscope. A comparative analysis was conducted with the annealed state of the alloy. The results show that after HIP, the TC4 alloy exhibits an elongated β columnar grain structure along the printing direction (vertical), while an equiaxed grain morphology is observed in the direction perpendicular to the printing (horizontal). Within the columnar grains, a mixed microstructure of α laths and α+β basketweave structures is present. Compared to the annealed state, the α laths in the HIP-treated alloy become wider, and the aspect ratio decreases. In contrast to the annealed state, the strength and plasticity of the HIP-treated alloy exhibit no significant anisotropy between the horizontal and vertical directions. The ultimate tensile strengths in the vertical and horizontal directions are 965 MPa and 975 MPa, respectively, while the elongations after fracture are 15.5% and 16.5%, respectively, demonstrating excellent overall mechanical properties. The tensile fracture surfaces exhibit dimples, indicating a ductile fracture mechanism. |
| Key words: TC4 alloy selective laser melting microstructure tensile property anisotropy |
|
|
|
|
