Lun JI , Jinqi WU , Hongzhuan LI , Zhice CHENG , Jiwei LIU , Yiqiu TAN
2024, 56(11):1-14. DOI: 10.11918/202307061
Abstract:In order to explore the physical characteristics and microstructure of mineral powder, and to conduct an in-depth study of the rheological properties of cement paste and the influence of mineral powder on the properties of cement paste, the physical characteristics, chemical composition and microstructure of different types of mineral powder were analyzed. Using different types of mineral powder with varying pass rates through a 0.075 mm sieve, asphalt mortar with different dosages was prepared. The influence of dynamic shear rheology and bending beam rheology test on the rheological properties of asphalt cement paste at high and low temperatures was analyzed. Gray relational analysis was employed to explore the relationships between the physical parameters and microstructural characteristics of the mineral powder and the high and low-temperature performance of the asphalt mortar. The experimental results show that the five types of mineral powders have relatively few small pores. The pores of R3 and R4 mineral powders are predominantly elongated, while the pores of R1, R2 and R5 mineral powders are mostly formed by particle accumulation. With the increase of mineral powder content, the overall high-temperature performance and anti-flow ability of asphalt mortar improve, while the low-temperature performance first weakens and then strengthens. Taking specific surface area and other indicators as comparison series and phase angle as reference series, the grey relational analysis method is used to determine that oxide content has the greatest influence on high temperature performance and the specific surface area of mineral powder has the least influence. At low temperature, the particle size of mineral powder has the greatest influence on creep stiffness, and the average pore diameter has the greatest influence on the change rate of creep stiffness. The control of mineral powder index and the change of high and low temperature characteristics can provide references for practical engineering applications.
Xiaoqing FENG , Bin YE , Husheng MIAO , Chuangji LIN
2024, 56(11):15-25. DOI: 10.11918/202305037
Abstract:In order to study the liquefaction of saturated foundation under dynamic conditions, a three-dimensional explicit material point method program MapleLeaf is developed by the interaction for the solid-liquid two-phase medium in this paper. Firstly, based on porous media theory, a single-point scheme is used to describe the solid-liquid two-phase medium. The formula of solid-liquid two-phase in the u-p scheme is derived. Secondly, the reliability of the numerical calculation under the solid-liquid two-phase static condition is verified by comparing the numerical results of the three-dimensional model of hydrostatic pressure column and the theoretical model of Terzaghi′s one-dimensional consolidation. Then, a dynamic algorithm module is added. And the Cyclic Mobility constitutive model for analyzing dynamic liquefaction is introduced into the program. Finally, based on saturated foundation model prepared from the existing literature and the shaking table system in the field, the three-dimensional numerical model is established. By comparing the numerical solution of the material point numerical model with the experimental results, the accuracy of the program in analyzing the liquefaction problem of saturated foundations under dynamic conditions is verified. The results show that the solid-liquid two-phase coupling numerical calculation method based on the material point method can better reflect the basic law of the growth and dissipation of excess pore water pressure before and after liquefaction of saturated foundation under dynamic conditions. The material point method program developed in this paper can accurately analyze the liquefaction of saturated foundation under dynamic conditions.
Xu JIANG , Hao QI , Xuhong QIANG , Kai SUN
2024, 56(11):26-35. DOI: 10.11918/202304069
Abstract:In order to further investigate the effects of hygrothermal ageing on the mechanical behavior of fiber reinforced polymer (FRP)-steel adhesively-bonded joints, based on existing studies, a series of loading tests were carried out on the hygrothermal ageing-treated FRP-steel adhesively-bonded joints by using a roulette wheel loading device, respectively, from six loading conditions, to study the effects of hygrothermal ageing on the ultimate failure loads, failure modes, stiffness and strength failure criteria of the FRP-steel adhesively-bonded joints, comparing results with the unaged adhesively-bonded joints. The results show that hygrothermal ageing significantly reduces the ultimate failure loads of the FRP-steel adhesively-bonded joints to 11.0 kN and 41.9 kN under shear and tensile loading, respectively. Under combined loading, the effect of hygrothermal aging on the ultimate failure loads was less pronounced. The strength failure criteria curves of the aged and unaged FRP-steel adhesively-bonded joints are close to each other. For tensile and tensile/shear combined loading conditions, hygrothermal aging altered the failure modes of FRP-steel adhesively-bonded joints, transitioning from partial interfacial failure between the FRP core plate and the structural adhesive layer to a combination of FRP delamination failure covering the entire structural adhesive bonding area and fiber fracture failure. Hygrothermal ageing significantly reduced the stiffness of the FRP-steel adhesively-bonded joints under all six loading conditions. Therefore, the effects of hygrothermal ageing on the mechanical behavior of FRP-steel adhesively-bonded joints should be fully considered when designing and using FRP-steel adhesively-bonded joints to avoid their structural damage.
Dongyue PAN , Qiong WANG , Wei SU , Weimin YE , Yang WANG
2024, 56(11):36-44. DOI: 10.11918/202310040
Abstract:To reveal the periodic changes in the water retention capacity of bentonite caused by the coupling of hydraulic and temperature during the operation of the multiple barrier system in the nuclear waste deep geological disposal repository, this work conducted a series of single/multiple suction cycle tests with temperature-controlled vapor equilibrium method and PEG dialysis method. The effects of the suction cycle and temperature on the water retention capacity of bentonite under free swelling conditions were investigated. Based on the test data, the Van Genuchten model for predicting the water retention curve of bentonite was modified and validated. Results show that in the single suction tests, the water content upon the drying path was always higher than that upon the wetting path, exhibiting hysteresis. As the temperature rising, the water retention capacity and hysteresis showed a decreasing trend. As the suction or cycle increasing, the hysteresis and thermal effect on water retention both decreased. In the multiple suction cycle tests, accumulation of water content was observed in each cycle. However, the multiple drying-wetting cycle accumulated more water content. As cycle increasing, the accumulation of water in each cycle decreased. The modified Van Genuchten model takes into account both temperature effects and the influence of suction paths. The predicted results have an error of less than 5% compared to the test result, which confirms the reliability of the modified model.
Jiangfeng WANG , Hao YANG , Yanping LIANG , Chuyao ZHANG
2024, 56(11):45-54. DOI: 10.11918/202311028
Abstract:To address the limitations of sparse mobile phone signaling data and the insufficient ability to extract and fuse features in trajectory reconstruction, this paper proposes a precise transportation mode recognition algorithm based on trajectory reconstruction and multi-source feature fusion. A wireless signal loss model is developed to characterize the signal path loss and signal strength of base stations. Using the hidden markov model (HMM), the mobile phone signaling trajectory is reconstructed from a base station sequence to a road segment node sequence. A trajectory reconstruction method based on the wireless signal propagation hidden markov model (WP-HMM) is proposed to describe the relationship between signal strength and distance. Based on the reconstructed travel trajectory and combined with the characteristics of road segment types, a spatiotemporal standardized similarity measurement fusion navigation trajectory feature is proposed, and a transportation mode recognition algorithm based on random forest (RF) is constructed. Empirical analysis shows that, through the reconstruction of travel trajectories, the model′s average recognition accuracy improved by over 8%, and it demonstrated excellent generalization ability for new samples. Compared to existing methods, the spatiotemporal normalized similarity measure more accurately captures the movement patterns between trajectories. In trajectory recognition across different environments, the model performs significantly better in suburban areas than in urban areas. The proposed algorithm demonstrates significant application value in the field of transportation mode recognition using large-scale mobile phone signaling data.
Baojie WANG , Jiping SHEN , Guohua LIANG , Xiangbei XUE
2024, 56(11):55-62. DOI: 10.11918/202310048
Abstract:In order to deeply understand the characteristics of the cross-type collision conflict between bus passengers crossing the non-motorised road to enter and exit bus stops and the longitudinal crossing of E-bikes, and to explore the factors influencing the severity of the conflict, a method for analyzing the safety impacts of E-bike crossings on the entering and exiting behaviors of bus passengers was proposed. Based on the trajectories of E-bikes and bus passengers obtained from aerial photography, the bus passenger-E-bike conflict was divided into three categories: bus passenger avoidance, E-bike avoidance, and both sides avoidance. Based on the characterization of cross-type conflicts, the relative collision time (TTR) indicator was proposed, and the conflict severity evaluation model based on improved K-means clustering was constructed by combining the post-trespassing time (PET) and safety deceleration speed (DST). Finally, five conflict severity influencing factors were extracted from the perspectives of bus passengers and E-bikes respectively, and a conflict severity level prediction model based on BP neural network was established and tested for model validity. The results show that speed difference and relative speed have the greatest influence on the conflict severity level. E-bike active avoidance has the least influence on the motion state of both parties in the conflict, and the relative collision energy is the lowest. The calculation results of the proposed conflict severity level prediction model have a high degree of conformity with the actual conflict level, and can predict the conflict severity level to a certain extent.
Jiajia WANG , Haojun CHEN , Lili XIAO , Zhiqiang LI , Zongrun CAI , Zhaolong SUN
2024, 56(11):63-71. DOI: 10.11918/202310045
Abstract:In order to further study the motion and accumulation characteristics and energy dissipation landslide debris flow, we established an experimental model of landslide debris flow by simplifying terrain features and considering key factors such as volume effect and start slip height. The characteristic parameters and accumulation process are monitored and obtained to reveal the kinematic characteristics of landslide debris flow. In addition, the TS method is used to simulate the movement process of landslide debris flow, and the key dynamic parameters are obtained by inversion. Combined with experimental and numerical methods, we quantitatively studied the motion process (distance, thickness, velocity, etc.), accumulation characteristics and energy conversion law of debris flow. The results show that the landslide volume and slip height have similar effects on the maximum movement distance of debris flow, while slip height has minimal effect on the width of accumulation body. The average velocity with time is in the form of a parabolic downward opening, and the peak velocity is obviously affected by height, and the velocity of the leading edge is greater than that of the middle and trailing edge. The conversion efficiency of the gravitational potential energy into kinetic energy is between 10% and 25%, and the conversion efficiency increases with the height of start slip, while the volume has little effect on the conversion efficiency. This paper comprehensively investigates the accumulation characteristics and energy dissipation law of landslide debris flow, and the results provide support for the study of the mechanism of landslide debris flow mechanics, which is of certain value for disaster prevention and mitigation.
Hengrui YOU , Zilong TI , Yongle LI , Ling YANG , Junzhi PAN
2024, 56(11):72-79. DOI: 10.11918/202303027
Abstract:In order to study the influence of different suspension-span ratios on the vortex-induced vibration performance of the beam in the cable-stayed-suspension cooperative system, a bridge with a cable-stayed-suspension cooperative system is used as the engineering background. Firstly, based on wind tunnel test, the method of Growth-to-resonance is used to obtain the development time history of the bridge section, which is in the process of VIV. Secondly, based on the nonlinear vortex-induced force model considering the span-direction amplitude dependence, the relationship curve of the aerodynamic damping parameters of the main girder section with the dimensionless amplitude is obtained through Hilbert transform. Finally, through iterative calculation of the beam VIV amplitude of eight alternatives. The change law of VIV in the processing of changing from the near-cable-stayed system to the suspension-cable system is clarified and a new evaluation index is proposed that considers the VIV amplitude value and the span-direction influence range. The results show that: with the increase of the hanging-span ratios, the corresponding first-order vertical bending mode shape changes from sharp to flat and the fundamental frequency decreases. As the hanging-span ratios increases, the vortex-induced vibration amplitude at mid-span consistently decreases. The variation in mid-span vortex vibration amplitude across different hanging-span ratios is approximately 11.1%. Additionally, the onset wind speed for the main girder′s vibration decreases with increasing hanging-span ratios. Combined with the average VIV amplitude value of the bridge (η*) and the average acceleration of the bridge (a*), the difference in η*under different hanging-span ratios is about 59.5%, and the influence on the overall VIV performance of the bridge is increasing, but the a* has limited change.
Zihao DING , Chuanhe LEI , Shixiong ZHENG , Hongyu JIA , Zhiqiang CHEN , Zhi XU
2024, 56(11):80-87,101. DOI: 10.11918/202310012
Abstract:To achieve rapid lateral capacity prediction of corroded RC columns without specific failure modes under seismic action, residual lateral capacity of corroded rectangular RC columns has been investigated based on machine learning (ML) methods. First, the input parameters for the ML model were determined, the dataset of corroded rectangular RC column was reorganized and correlations among the input parameters were analyzed. Then, six typical ML algorithms, including SVM, KNN, ANN, CNN, RF and CatBoost, were selected to establish the ML models for lateral capacity of corroded RC columns, and the hyper-parameters of ML models were optimized and determined using grid search or trial-and-error methods as well as 5-fold cross-validation. Finally, the predictive accuracy of the six ML models was evaluated based on four widely-used regression evaluation metrics (EMA, ERMS, EMAP and R2) and testing set, and the importance ranking of input parameters and parameter sensitivity analysis were carried out based on the excellent ML models. Results show that the predictive performance of neural network models is generally better than that of ensemble models or other single models, in which ANN model is more satisfactory, and the mean and standard deviation of the ratio of its predicted result to experimental value are 1.01 and 0.14, respectively. Shear-span ratio has the highest and significant effect on the lateral capacity of corroded rectangular RC columns, with an importance of up to 35%. The lateral capacity of rectangular RC columns decreases with the increase of shear-span ratio, the ratio of stirrup spacing to section effective height and corrosion level, but increases at first and then tends to stabilize or decrease with the increase of axial load ratio.
Pengyu CHEN , Bingchen YANG , Tianyun YAO , Fangzhou XU , Yu ZHAO , Yongjun ZHOU
2024, 56(11):88-101. DOI: 10.11918/202310014
Abstract:In order to test and analyze the mode Ⅰ inter-layer fracture toughness of 3D printing carbon fiber reinforced polymer (CFRP), and quantitatively evaluate the influence of printing parameters on the mode Ⅰ fracture toughness, then promote the application of 3D printing CFRP technology in bridge engineering, experimental and simulation methods were used to carry out the relevant explorations, during this study. Firstly, a novel method for preparing inter-layer pre-cracks of 3D printing CFRP was proposed, namely fracture layer replacement method. Systematic experimental research was conducted by this method, and the influence of two types of key printing parameters on the mode Ⅰ inter-layer fracture toughness was analyzed. Secondly, based on the cohesive zone theory and the surface-based cohesive relationship, simulation models of the double cantilever beam (DCB) test specimens with pre-cracks under various printing conditions were established. Meanwhile, a comparative analysis between simulation and experiment was carried out. The results indicate that the mode Ⅰ inter-layer fracture toughness of 3D printing CFRP increases with the increase of printing temperature and printing speed, and the effect of printing temperature is more significant. When the temperature increases from 245 ℃ to 285 ℃, the fracture toughness increases by 294.6%. When the printing speed increases from 20 mm/s to 60 mm/s, the fracture toughness increases by 27.6%. When the printing temperature and speed are increased, the heat loss of specimen in the printing process is smaller, and the mode Ⅰ inter-layer mechanical properties are improved. However, excessive printing speed can hinder complete deposition and optimal bonding, resulting in negative effects on the mode Ⅰ inter-layer mechanical properties. Moreover, the relative errors between simulation results and experimental data are controlled within 15%, which indicates that the fracture replacement method proposed in this study is reasonable and stable in terms of obtaining test data of type Ⅰ inter-layer fracture toughness. Therefore, this method can provide experimental technical support for the subsequent quantitative evaluation of inter-layer mechanical properties of 3D printing CFRP bridge engineering components.
Lili XIAO , Tiantian LI , Jiajia WANG , Liran NIU
2024, 56(11):102-114. DOI: 10.11918/202403047
Abstract:To clarify the influence of mechanical effects on the surge scale during the generation process of landslide-generated tsunami, this paper supplements the explanation of the volume Lift Up (LU) correction model and its application range based on a dynamic model of the landslide-generated tsunami generation process under the coupling of LU, PA, DA. Taking several scenarios in the 3D granular landslide surge physical model experiment as the research object, combined with the Tsunami Squares numerical simulation method, the contributions of LU, PA, and DA to the wave amplitude and wave energy of the surge are analyzed, revealing the characteristics and mechanisms of each mechanical effect during the generation process of landslide-generated waves. The results show that: When the ratio of water depth to block side length is less than 1/5, the BT correction can be ignored; PA has a more significant acceleration effect on the water than LU, and the contribution rates of PA and DA to the initial surge wave height reach 29% and 9% respectively, and both decrease with the increase of propagation distance; PA contributes to the potential energy, kinetic energy, and total energy of the surge by 23%-30%, 28%-29%, and 25%-30% respectively, while DA contributes to the three types of energy by 17%-25%, 14%-16%, and 16%-23% respectively, and LU&BT contributes the remaining energy. This study reveals the dynamic mechanism of landslide-generated tsunami, providing a dynamic model and parameter selection basis for the prediction and evaluation of landslide-generated tsunami disasters.
Bin ZHANG , Yuxiang GAO , Zaigang CHEN , Kaiyun WANG , Jin SHI
2024, 56(11):115-122. DOI: 10.11918/202312007
Abstract:In order to achieve accurate prediction of rail wear on small radius curve of heavy-duty railway, a prediction model for rail wear combining improved particle swarm optimization with BP neural network and the GM(1,1) model is proposed. First, the calculation method of background value of is optimized according to the principle of integration, and preliminary prediction results of wear are obtained based on the improved model. Then, the weights and thresholds in network structure nodes of the BP model is optimized by using the IPSO algorithm, and the residual values of the preliminary prediction results are corrected. Finally, the optimized two models are combined to construct a prediction model for rail wear in small radius curve of heavy-duty railways based on GM(1,1)-IPSO-BP model. Taking a curve with 400 m radius on a Heavy Duty Railway bridge as a case study, applicability analysis of the method in this article is analyzed using long-term wear monitoring data. The results show that the GM(1,1)-IPSO-BP model overcomes the influence of nonlinear and random characteristics of wear data on the calculation results, and its prediction accuracy is superior to using GM (1,1) and IPSO-BP alone. The GM (1,1) model with optimized background values has more reliable prediction accuracy. Prediction accuracy and calculation speed of the BP network optimized by the IPSO algorithm is improved. The relative error between the predictive value calculated with this model and the detection value is less than 4%, and the absolute error of abrasion value is not more than 0.4 mm. Through this method, the development law of rail wear can be accurately obtained. The research results could provide reference for the precise maintenance and scientific use of small radius curve rail in heavy haul railways.
Jinbo TIAN , Yonggan ZHANG , Yang LU , Wenxin MA , Sihong LIU , Liujiang WANG , Jin LIU
2024, 56(11):123-131. DOI: 10.11918/202404051
Abstract:In order to explore the influence of initial saturation on the low-temperature mechanical properties of canal expansive soil, the unconfined compressive strength tests under -2 ℃, -5 ℃, -10 ℃ and -15 ℃ were carried out on canal expansive soil with different initial saturation. The effects of temperature and initial saturation on the strength and deformation characteristics of canal expansive soil are discussed. The results show that: the stress-strain curves of the samples gradually transform from softening type to hardening type with the increase of initial saturation. Two different types of stress-strain relationship can be described by hyperbolic equation and composite index equation respectively. According to the failure characteristics, the failure modes of the samples can be divided into three types: collapse failure, bulging failure and overall compression failure. At -2 ℃, the compressive strength of the sample decreases with the increase of initial saturation, but at -5 ℃, -10 ℃ and -15 ℃, the compressive strength increases first and then decreases with the increase of initial saturation, there is a "critical saturation" that makes the sample have the strongest resistance to failure, and this "critical saturation" decreases with the decrease of test temperature. In addition, with the decrease of test temperature, the elastic modulus and compressive strength of the sample increase gradually, but the hardening modulus of the sample increase first and then decreases.
Guozhu CHENG , Changru MU , Gangrui JIN , Yulong PEI , Liang XU
2024, 56(11):132-139. DOI: 10.11918/202305059
Abstract:To quantitatively evaluate the risk of roadside accidents for low-grade highway trucks and reduce roadside accident losses, simulation experiments were conducted using PC Crash software to study the accidental severity of light and heavy trucks entering the roadside under different circular curve radius, slope gradient, exit speeds, and roadbed heights. The acceleration damage index ASI is used as the evaluation index of passenger injury, and the calculation models of passenger injury degree of truck side accidents in linear and curved sections of low grade highway are established respectively. By using Fisher′s optimal segmentation method and ASI ordered data samples. The roadside accident severity grade of low-grade highway trucks is divided and the ASI threshold of acceleration damage index is calculated. and the severity evaluation criteria of truck side accidents on low grade highway were put forward. The results show that the acceleration damage index ASI exhibits a similar positive linear trend with vehicle speed and roadbed height. The change trend between acceleration damage index ASI and slope gradient is similar to that of Exponential function. The change trend between the acceleration damage index ASI and the radius of the circular curve is similar to that of the power function. Compared with vehicle speed and roadbed height, the increase of slope gradient is more likely to lead to roadside accidents when vehicles rush out of the road and increase the severity of roadside accidents. However, although increasing the radius of circular curves can reduce the severity of roadside accidents, its impact is relatively small.
Xiaodong ZHANG , Zhejin LU , Min LIU , Feng YANG , Lianheng ZHAO
2024, 56(11):140-150. DOI: 10.11918/202403062
Abstract:In order to explore the impact of the dynamic changes in the actual infiltration capacity of the soil during rainfall on the rainfall infiltration patterns and stability of slopes. From the perspective of soil gradation characteristics, this paper first derives an analytical model for the saturated permeability coefficient of soils with different gradation characteristics based on fractal theory. Further considering the influence of the elliptical transition zone in the infiltration area, the equivalent permeability coefficient of the infiltration area is corrected in real-time based on the thickness ratio between the transition zone and the infiltration area under different rainfall durations. An improved GA infiltration model for soils with varying gradation characteristics is proposed. Finally, based on the improved GA infiltration model, a modified shallow slope stability analysis model is established, which takes into account the variation of soil shear strength with gradation characteristics and rainfall duration. Comparison with existing results shows that the model presented in this paper can accurately characterize the infiltration state of the soil and the changes in shear strength during rainfall. Parameter analysis indicates that the pore distribution characteristics of the soil are significantly positively correlated with the saturated permeability coefficient, which directly affects the moisture profile distribution within the slope and the timing of surface runoff occurrence. The migration rate of the wetting front increases with the initial moisture content of the slope, leading to a reduced proportion of the transition zone in the infiltration area under the same rainfall duration, which in turn dynamically affects the equivalent permeability coefficient of the infiltration area. The stability of the slope′s transition zone is significantly influenced by soil gradation characteristics and initial moisture content, making the slope prone to instability and failure within the transition zone. Therefore, in slope instability analysis under heavy rainfall, special attention should be paid to the stability of the infiltration area′s transition zone.
Yuanqiao WEN , Xiaodong CHENG , Liang HUANG , Yamin HUANG , Shunqiang XU , Shubin ZHONG
2024, 56(11):151-161. DOI: 10.11918/202310060
Abstract:To achieve semantic expression and reasoning of scenarios under the International Regulations for Preventing Collisions at Sea (COLREGs), enabling ships to understand and reason about waterborne traffic scenarios similarly to humans, a scenario cognition computing modeling method incorporating COLREGs is proposed. Based on the semantic description of waterborne traffic scenarios under COLREGs, this approach parses the scenarios into a comprehensive system of interactions among elements such as time, objects, attributes, relations, behaviors, and events, thereby constructing a conceptual model of waterborne traffic scenarios. It employs ontological modeling to structure the expression of the COLREGs scenario conceptual model. Through defining semantic computational operation functions and trigger sets, a COLREGs scenario cognition computing framework is established, leading to the proposal of a logic reasoning-based scenario cognition computing method. The model is validated with case studies using the environment of Xiamen Port and ship AIS data based on semantic extraction from scenarios. The results shows that, compared to data-driven model, the proposed model can describe and computationally process object attributes, ship behaviors, and traffic events in scenarios, and support the acquisition and querying of related knowledge of various elements within the scenario. The proposed scenario cognition modeling method is feasible and effective for enabling autonomous scenario cognition of ships under rule constraints.
Huan WANG , Ling KANG , Ming CHEN , Qi ZOU , Tingmin MU
2024, 56(11):162-170. DOI: 10.11918/202408057
Abstract:To investigate the weak confinement effect of concrete-filled thin-walled steel box (CFTSB), the axial compression tests of 9 CFTSB short columns and 6 control group tests of circular concrete-filled steel tube (CFST) and ordinary reinforced concrete (RC) short columns are carried out. The mechanical behaviors such as failure mode, load-displacement curve, ultimate bearing capacity, composite strength, axial compression stiffness, and sectional strain distribution were obtained, and the weak confinement effect of CFTSB and the deformation coordination relationship between thin-walled steel box and concrete are described in detail by comparing with circular CFST and ordinary RC components. Based on the contribution of thin-walled steel box to the strength improvement of concrete, an axial compressive capacity calculating method of CFTSB short column with weak confinement effect is established. The results show that the ultimate bearing capacity and axial compression stiffness increase with the increase of steel ratio and confinement coefficient, but decrease with the increase of width-to-thickness ratio. Under the weak confinement effect, the thin-walled steel box partially buckled at 30%-40% of the ultimate load, and then the deformation of the steel box and concrete appeared uncoordinated phenomenon. The concrete is crushed when it reached ultimate state, and the bearing capacity declined rapidly because of the decrease of effective bearing area, but the ductility during later period is better maintained by the steel box. In the case of small steel ratio, the mechanical behavior of CFTSB and CEST is similar in elastic and elastic-plastic stage as well as similar ultimate bearing capacity and axial compressive stiffness, but the circular section shows ductile failure and the constraint effect of falling stage is better than that of the rectangular section. The bearing capacity and stiffness of CFTSB are about 15% and 5% higher than that of ordinary RC, respectively, and the construction does not need to tie steel bars and install and disassemble formworks. The proposed bearing capacity calculation method is proved to be reliable and can provide useful guidance for the design of CFTSB structure.
You are the visitor 
Address:Box 136, 92 Xidazhi Street, Nangang District, Harbin
Postcode:150001 E-mail:hitxuebao@hit.edu.cn
ICP:京ICP备09084417号-23
Copyright:Journal of Harbin Institute of Technology ® 2026 All Rights Reserved
