一种基于新型增敏结构的高强螺栓紧固力监测智能垫圈
CSTR:
作者:
作者单位:

(1.哈尔滨工业大学 土木工程学院,哈尔滨 150090; 2.交通基础设施智能监测与预警工业和信息化部重点实验室(哈尔滨工业大学),哈尔滨 150090)

作者简介:

韩坤(2000—),男,博士研究生;张东昱(1974—),男,教授,博士生导师

通讯作者:

中图分类号:

TP212

基金项目:

国家重点研发计划(2022YFB3706704);国家自然科学基金(U2239253)


A smart washer sensor based on a novel sensitivity-enhanced structure for monitoring tightening force of high-strength bolts
Author:
Affiliation:

(1.School of Civil Engineering, Harbin Institute of Technology, Harbin 150090, China; 2.Key Laboratory of Intelligent Monitoring and Early Warning of Transportation Infrastructure (Harbin Institute of Technology), Ministry of Industry and Information Technology, Harbin 150090, China)

Fund Project:

undefined

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    高强螺栓连接广泛应用于各类工程结构,螺栓紧固力衰减导致连接松动可能会对结构安全服役构成严重威胁。压力垫圈是监测螺栓紧固力常用传感器,然而对于大荷载高强螺栓,传统压力垫圈存在传感器尺寸大、测量精度易受荷载偏心及传感器与结构表面摩擦等因素影响的缺点,难以满足工程应用需求。为此,提出一种具有新型增敏结构的高强螺栓紧固力监测智能垫圈传感器。与传统压力垫圈采用单一圆环形结构不同,本研究提出的智能垫圈由3层环形结构叠合构成,中间测量单元与上/下部传力单元之间接触面为向内倾斜环形。这种独创的增敏结构将智能垫圈所受的螺栓竖向压力转化为中间测量单元水平环向膨胀变形,不仅大幅增加智能垫圈测量灵敏度,还消除了智能垫圈与结构接触表面摩擦力对测量精度的不利影响。通过理论分析和数值模拟,研究了智能垫圈设计参数对其灵敏度、量程等关键测量指标的影响规律,并提出一种智能垫圈加卸载全过程分段测量模型,解决了倾斜接触表面间摩擦力导致智能垫圈加卸载过程测量结果不一致问题,进一步提升了测量精度。最后,研制了一个量程700 kN智能垫圈传感器并开展检测实验,结果表明,传感器平均测量误差仅为3 kN。提出的智能垫圈传感器具有体积小、量程大和精度高等优点,具有广阔工程应用前景。

    Abstract:

    High-strength bolted connections are widely used in various engineering structures, and connection loosening caused by the attenuation of bolt tightening force may pose a serious threat to structural safety. Pressure washers are commonly used sensors for monitoring bolt tightening force. However, for high-strength bolts subjected to large loads, traditional pressure washers have drawbacks such as large sensor size and measurement accuracy that is easily affected by factors including load eccentricity and friction between the sensor and the structural surface, making it difficult to meet the requirements of engineering applications. To address this issue, this paper proposed a smart washer sensor with a novel sensitivity-enhanced structure for monitoring the tightening force of high-strength bolts. Different from traditional pressure washers using a single ring-shaped structure, the proposed smart washer consists of three layers of stacked ring-shaped structures, and the contact surfaces between the middle measuring unit and the upper/lower force transmission units are inwardly tilted annular surfaces. This original sensitivity-enhanced structure converts the vertical bolt pressure on the smart washer into horizontal circumferential expansion deformation of the middle measuring unit, which not only significantly increases the measurement sensitivity of the smart washer but also eliminates the adverse effects of friction between the smart washer and the structural contact surface on measurement accuracy. Through theoretical analysis and numerical simulation, the influence rules of the design parameters of the smart washer on its key measurement indicators such as sensitivity and measurement range were investigated, and a segmented measurement model for the entire loading and unloading processes of the smart washer was proposed. This model solved the problem of inconsistent measurement results during the loading and unloading processes of the smart washer caused by friction between the tilted contact surfaces and further improved the measurement accuracy. Finally, a smart washer sensor with a measurement range of 700 kN was fabricated and tested. The experimental results indicate that the average measurement error of the sensor is only 3 kN. The proposed smart washer sensor has the advantages of small volume, large measurement range, and high accuracy, which has broad engineering application prospects.

    参考文献
    相似文献
    引证文献
引用本文

韩坤,张东昱,李惠,倪莉.一种基于新型增敏结构的高强螺栓紧固力监测智能垫圈[J].哈尔滨工业大学学报,2026,58(10):72. DOI:10.11918/202506042

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2025-06-18
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-10-27
  • 出版日期:
文章二维码