悬索桥主缆缠丝张力损失特征与机理
CSTR:
作者:
作者单位:

(1.陕西省“四主体一联合”桥梁工程智能建造技术校企联合研究中心,西安 710199; 2.中交第二公路工程局有限公司,西安 710065;3.长安大学 公路学院,西安 710064)

作者简介:

肖军(1987—),男,工学博士,高级工程师

通讯作者:

中图分类号:

U443

基金项目:


Characteristics and mechanisms of tension loss in the helical wrapping wires of main cables in suspension bridges
Author:
Affiliation:

(1.Shaanxi Union Research Center of University and Enterprise for Bridge Intelligent Construction, Xi′an 710199, China; 2.CCCC Second Highway Engineering Bureau Co., Ltd., Xi′an 710065, China; 3.School of Highway, Chang′an University, Xi′an 710064, China)

Fund Project:

undefined

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为研究悬索桥主缆缠丝的防护效果,采用精细化有限元模型结合实桥试验的方法研究了缠丝过程中的缠丝张力变化,并基于验证后的有限元模型分析了缠丝导入力、主缆直径及主缆径向弹性模量对缠丝张力损失的影响,提出了考虑缠丝阶段张力损失的缠丝导入力计算公式并改进了现有缠丝工艺。试验研究结果表明:缠丝阶段的张力损失主要是由后续缠丝张力引起主缆径向变形导致,张力损失呈现先快后慢,然后逐渐趋于稳定的特征,缠丝阶段的张力损失在26.3%~37.3%之间;测试位置处缠丝张力稳定时,缠丝机较测试位置处平均前进距离为25.2 cm。有限元分析结果表明:主缆直径及径向弹性模量对缠丝力损失比例影响显著,且主缆直径及径向弹性模量与缠丝力损失比例均成反比例关系;主缆直径为851.9 mm情况下,主缆直径增大50%,缠丝力损失比例从27.8%减小至13.7%,主缆径向弹性模量从1 052 MPa增加至3 052 MPa,缠丝力损失从27.8%减小至11.3%。在试验及有限元分析结果基础上,提出了考虑缠丝阶段张力损失的导入力计算公式,进一步优化了缠丝导入力的计算;提出了一种基于缠丝张力损失机理的新型缠丝工艺,可有效减小缠丝过程中的张力损失。

    Abstract:

    To investigate the protective effectiveness of strand wrapping wire in suspension bridge main cables, a method combining refined finite element models with full-scale bridge testing was adopted to study the variations in wrapping wire tension throughout the process. Based on the validated finite element models, the impacts of the wrapping wire insertion force, main cable diameter, and main cable radial elastic modulus on tension loss were analyzed. A formula for calculating the wrapping wire insertion force, which takes into account tension loss during the wrapping wire stage, was proposed, and the existing wrapping wire process was improved. Experimental results indicate that tension loss during the wrapping wire stage is primarily caused by radial deformation of the main cable due to subsequent wrapping wire tensions. The tension loss exhibits an initial rapid decrease, followed by a slower rate, and gradually stabilizes, ranging between 26.3% and 37.3%. When the wrapping wire tension stabilizes at the test location, the wrapping wire machine advances an average distance of 25.2 cm relative to the test position. Finite element analysis results reveal that the main cable diameter and radial elastic modulus have significant effects on the proportion of wrapping wire force loss, with both factors showing an inverse proportional relationship with the force loss ratio. In the case of a main cable with a diameter of 851.9 mm, an increase in the main cable diameter by 50% reduces the wrapping wire force loss ratio from 27.8% to 13.7%, and an increase in the main cable radial elastic modulus from 1 052 MPa to 3 052 MPa reduces the force loss from 27.8% to 11.3%. Based on the experimental and finite element analysis results, a formula for calculating the insertion force that considers tension loss during the wrapping wire stage was further refined. Additionally, a novel wrapping wire process based on Mechanism of wrapping wire tension loss was introduced, which can effectively reduce tension loss during the wrapping wire process.

    参考文献
    相似文献
    引证文献
引用本文

肖军,霰建平,仝朝康,马建勇,王培杰,刘永健.悬索桥主缆缠丝张力损失特征与机理[J].哈尔滨工业大学学报,2026,58(7):166. DOI:10.11918/202412066

复制
分享
相关视频

文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2024-12-23
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2026-09-29
  • 出版日期:
文章二维码