| 引用本文: | 付佳玉,刘伟东,陈宇航,冯祥雨,崔庆辉.Mg/Si比对AlMgSiCu合金时效析出相及性能的影响[J].材料科学与工艺,2026,34(5):88-96.DOI:10.11951/j.issn.1005-0299.20250054. |
| FU Jiayu,LIU Weidong,CHEN Yuhang,FENG Xiangyu,CUI Qinghui.Effect of Mg/Si ratio on theaging precipitation phase and properties of AlMgSiCu alloys[J].Materials Science and Technology,2026,34(5):88-96.DOI:10.11951/j.issn.1005-0299.20250054. |
|
| 摘要: |
| Mg/Si比是影响AlMgSi系合金微观组织、时效析出行为、力学性能以及导电性能的关键因素。为了研究Mg/Si比对时效析出相及性能的影响,采用SEM、EDS、XRD等测试手段分析了不同Mg/Si质量比(0.82、1.3、1.73、2.27、2.72)的AlMgSiCu合金的显微组织、相组成以及显微硬度,并分析了析出相含量与温度的关系,模拟计算了合金的电导率和时效抗拉强度。研究表明:随着Mg/Si比的增加,AlMgSiCu合金铸态组织由树枝晶向等轴晶和鱼骨状组织转变;当Mg/Si=1.73时,AlMgSiCu合金铸态硬度(89.9HV)最高,晶界处存在的网状分布的第二相主要是β相和θ相。与铸态相比,经T6时效处理后,AlMgSiCu合金中没有新的第二相产生,但晶界处第二相数量减少,晶内析出相的数量增多。与Mg/Si比分别为0.82、1.73、2.27、2.72的时效态合金相比,Mg/Si比为1.3的AlMgSiCu合金时效态硬度最高,峰值硬度(116.3HV)和抗拉强度(276.68 MPa)最大,时效硬化响应速率最快。合适的Mg/Si比可使AlMgSiCu合金时效后具有更高的硬度、强度和更好的导电性。 |
| 关键词: AlMgSiCu合金 Mg/Si比 微观组织 时效处理 析出相 性能 |
| DOI:10.11951/j.issn.1005-0299.20250054 |
| 分类号:TG111.1 |
| 文献标识码:A |
| 基金项目:辽宁省教育厅面上项目(LJKMZ20220958、LJK20621);辽宁省“兴辽英才计划”教学名师项目(XLYC221026). |
|
| Effect of Mg/Si ratio on theaging precipitation phase and properties of AlMgSiCu alloys |
|
FU Jiayu,LIU Weidong,CHEN Yuhang,FENG Xiangyu,CUI Qinghui
|
|
(School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou 121001, China)
|
| Abstract: |
| The Mg/Si mass ratio plays a pivotal role in determining the microstructure, aging precipitation behavior, mechanical properties, and electrical conductivity of AlMgSi series alloys. To study the effect of Mg/Si ratio on the aging precipitation phases and properties, SEM, EDS, and XRD were used to analyze the microstructure, phase composition, and microhardness of AlMgSiCu alloys with different Mg/Si mass ratios (0.82, 1.3, 1.73, 2.27, 2.72). Additionally, the relationship between the content of precipitated phases and temperature was analyzed, and the alloy’s electrical conductivity and aged tensile strength were simulated. The results show that as the Mg/Si ratio increases, the as-cast microstructure of AlMgSiCu alloys transforms from dendritic structure to equiaxed grain and fishbone-like microstructure. The highest as-cast hardness (89.9HV) is obtained at the Mg/Si ratio of 1.73, where second phases predominantly composed of β and θ phases exhibited a net-like distribution along the grain boundaries. In comparison to the as-cast condition, no new second phases precipitated after T6 aging treatment, however, the amount of second phase at the grain boundary decreases while intragranular precipitation increases. Compared with the aged alloys of the Mg/Si ratios (0.82, 1.73, 2.27 and 2.72), the 1.3 Mg/Si ratio alloy achieves the highest aged hardness, peak hardness(116.3HV) and tensile strength(276.68 MPa) with the fastest aging response. The higher hardness, bigger strength and better electrical conductivity of AlMgSiCu alloys can be obtained with suitable Mg/Si ratio. |
| Key words: AlMgSiCu alloy Mg/Si ratio microstructure aging treatment precipitated phase properties |